Step 5: Reinstalling the drivers for the drive In Windows XP, click Start, right-click My Computer, and select Properties. The 00 means that no fault was found. 201 would mean a memory error. 202 would mean memory address error; lines 00-15. Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Verify that the floppy cable coming from the motherboard is connected to the back of the floppy drive. weblink
I have swapped one end of the cable with the other. If you have a bootable diskette in the drive and still receive this error, the cable to the floppy cable is loose or defective. 0Votes Share Flag Back to Hardware Forum Dive into the retro feeling and build yourself a Commodore PET replica Need more speed? In Windows 98 and Me, click the Device tab and select the Manager View devices by type option. http://www.computerhope.com/issues/ch000277.htm
After Windows has fully loaded, test the floppy drive. Replace it with another available power lead that appears similar to the one originally on the drive. The disk in drive A is not formatted.
It stated Bios battery failure. If the problem persists, replace the diskette/CD-drive subsystem. Solution: Insert a disk into the floppy drive. The Disk Media Is Not Recognized Floppy Helpful +9 Report Bigane Aug 26, 2008 07:23AM I had the same bother and it was enabling floppy disc drive which I dont have.go to bios f2 and click on load
Originally Posted by lowen It's 8748 code, and so it wouldn't be super hard to reverse-engineer. Floppy Disk Drive Problems I do have the "Diskette Drive 0 Seek Failure" message come up and it has also told me that the "Diskette Drive (B)" is corrupt. I was told by a computer shop that my hard drive needs to be replaced. http://answers.microsoft.com/en-us/windows/forum/windows_7-files/floppy-read-error-0x800706f9/ccdd4a96-e23d-46f1-97ea-53fccd55753f Helpful +1 Report anil Aug 8, 2008 03:18PM Hi this might happen becaue of Faulty or improperly installed diskette, loose diskette/CD interface cable, or loose power cable.Replace the diskette.
They asked me to purchase at recovery disk, and I said taht i'll need to thik about it so they're calling me tomorrow on april 21st around 9-10 pm eastern. Floppy Disk Driver Windows 7 Report HOBBY- Apr 29, 2010 08:14AM I JUST RAN INTO THIS PROBLEM ALSO AND TRIED THIS STEP BY STEP AND IT WORKED , SO GLAD BECAUSE IT WAS GETTING TO BE The single sided drives could even read the double sided disks, as long as the second side was not used. once again thanks and good luck ^_^ Report Warlock- Apr 12, 2010 07:41PM thanks man you know about computers Report NoRule- Apr 19, 2010 08:01PM skillz dat killz Report mathgeek- Apr
However, I have a drive that is flashing in an undocumented sequence: 3 flashes, then 1. Continued The system's CMOS settings may be incorrect. Floppy Disk Problems And Solutions Reinsert both cables into the back of the drive. How To Read A Floppy Disk Without Formatting It The board reset when I removed the battery.
The power connector to the floppy may be loose or disconnected. have a peek at these guys Refer to Updating Drivers and Software Using Windows Updates for more help with Windows Update. You might put a meter on the sensor ( switch or opto transistor ) and see if it is detecting the track 0 position. If your floppy cable has more than one connection, verify that you have connected the floppy to the appropriate connection. Floppy Disk Format Error
I do not know how to get into the BIOS on XP. At Startup press "F2" to enter setup; Arrow down to select "Boot device configuration" - press enter; Arrow down to select "1st boot device" - press enter; Arrow cursor to select Checking the cablesIf you have checked the CMOS settings and the settings are correct, the problem may be a poor connection between the floppy drive and the system board or controller. http://bigvideogamereviewer.com/floppy-disk/floppy-drive-recovery.html If you're new to the TechRepublic Forums, please read our TechRepublic Forums FAQ.
System Board Errors: Code Description 101 System board interrupt failure (unexpected interrupt) 102 BIOS ROM checksum error (PC, XT); timer error (AT, MCA) 103 BASIC ROM checksum error (PC, XT); timer I then changed the bios battery inside the pc by opening the side of the case and removing the little flat 3v battery and replacing it with a new one. *** This document helps resolve floppy drive failures and errors. Floppy Disk Not Accessible I am making the assumption your original comment was meant to indicate what the drives does the instant you closed the door, after you had inserted a disk, then allowing it
But what are the odds 4 out of 4 drives failed? Here's a copy of the manual I'm using: https://dl.dropboxusercontent.com/u/...anual_1983.pdf Pete http://pski.net Reply With Quote August 24th, 2016,12:02 PM #2 lowen View Profile View Forum Posts Private Message View Blog Entries View Pari Report sealtsswine- Jun 2, 2009 11:31AM very much a novice- please help I have the same problem with a dimension 3000 I went to F2 then I am not sure this content Today you are my hero.
The method for reading these codes is pretty straight forward. if it don't tell me your hard drive configuration and I shall help you. I then checked the system event log on the bottom. Report crnyman1 2Posts Monday November 30, 2009Registration date December 1, 2009 Last seen - Dec 1, 2009 03:13AM Thank you SOOOOOO much!
If you do not have a tab place tape over this hole. If neither of those changes work, get a new FDD (they are mechanical, and they do wear out). Pete http://pski.net Reply With Quote August 24th, 2016,03:15 PM #4 pski View Profile View Forum Posts Private Message View Blog Entries View Articles Moderator Join Date Nov 2014 Location New York I so appreciate your information.
Being serious now, does it make the same flash sequence and grunt if you have the door open and no disk in drive ? HP and Compaq Desktop PCs - Floppy Drive Troubleshooting Troubleshooting the floppy drive Error message: The disk may be write protected Floppy disk is stuck in drive Clicking noise coming from It does step out and seems to groan when it hits the stop at the other end but then never goes back to track 0. In Windows XP, click the Hardware tab and then the Device Manager button.
Unfortunately, apparently I have been "pressing F1" for too long. Eliminating possible conflicts with other hardware If you have recently installed any new hardware, you should consider disconnecting it temporarily it to ensure that it is not the cause of your