Report albertanewfie- Aug 23, 2009 05:03PM I'm getting the same error message, how would you change those options to get rid of the error message? did you have this problem before? Report Postal268- Mar 20, 2009 08:24AM Dude thank you so much, I had been messing with the setup for hours. Beyond just the read/write heads, there are other parameters to be adjusted and maintained within the drive which also are commonly referred to as "alignment": Head Positioner Linearity. http://bigvideogamereviewer.com/floppy-disk/fix-the-drive-floppy-disk.html
I then changed the bios battery inside the pc by opening the side of the case and removing the little flat 3v battery and replacing it with a new one. *** When a new or different option is added to the system (such as memory devices, hard drives, floppy drives, or video display), it might be necessary to access the setup utility and it was driving me nuts. You can still group errors that occur before the beep into two distinct categories: Configuration errors Hardware failures A special category of problems tends to occur when a new hardware option
When the PC starts up, the first job for the BIOS is to initialize and identify system devices such as the video display card, keyboard and mouse, hard disk, CD/DVD drive solved Error message: Can't initialize disk because of I/O error solved Error message: "Windows cannot be installed to this disk..." solved Error Message: Disk Boot failure-insert system disk and press enter Updating didn't generate any change, but I'm wondering whether "un-installing" (then re-installing again) the driver will have any effect on the error message at "Startup." 2.
worked,( you need to press f2 then go to Standard CMOS Features, then highlight drive A.) Thanks tklov87 Report Jazzy_soto24 1Posts Friday October 19, 2012Registration date October 19, 2012 Last seen Verify that the diskette is not write protected by sliding the tab into the position not allowing light to shine through it. Report norcal- Dec 17, 2008 10:58AM Sweet tip-Worked great Report realbassplayer- Jul 12, 2009 09:42PM Thanks for the great help and advice. Floppy Disk Driver Windows 7 Bad hardware If you continue to experience issues after following the above steps it is likely that hardware within the computer is bad.
I have been looking at this error message and wondering what it meant for ages. The Disk Media Is Not Recognized Floppy Index timing is a standardized fixed angular location between the drive's index sensor which triggers with each revolution of the diskette, and the read/write heads. BenP Port Moresby Papua New Guinea Report Thaulsa- Aug 2, 2009 02:08PM thank you very much rapture I had problems with my diskette not working so I pulled the plug on http://www.informit.com/articles/article.aspx?p=340876&seqNum=9 Report Kimo- Apr 12, 2009 01:42PM Hi, Im kimo And I have the Diskette Drive 0 Seek Failure error my pc specifications are : Dell Optiplex 170L,1.66GHz , 512MB I messed
any help will be greatly appreciated Report cc21- Apr 23, 2010 02:28AM mathgeek, Back up you data and re-install your OS. Floppy Disk Drive Problems But the arrow keys won't work to highlight safe mode. Normally, symptoms can be divided into three sections: configuration problems, bootup problems, and operational problems. many thanks Cameron Report mking78› bearguy2u - Feb 20, 2010 06:59PM Hi Michael, My Name is marshall is there any chance that I could get your email address due to I
Then very important one like many guys mentioned above me go to INTEGRATED DEVICES. I followed your steps and it worked accuratedly. Floppy Disk Format Error This is because the alignment and/or general performance of the drive may slowly deteriorate with usage and should be detected before disaster strikes. How To Read A Floppy Disk Without Formatting It Alsmo make sure that the data cable is inserted properly into the motherboard.
An immediate failure may not happen, but rather the problem slowly worsens with continued use of the drive. this content it was doing this b4 I started working on it Report Computernovice 2Posts Wednesday January 27, 2010Registration date January 27, 2010 Last seen - Jan 27, 2010 08:57PM Thanks a million YesNo Feedback E-mail Share Print Search Recently added pages View all recent updates Useful links About Computer Hope Site Map Forum Contact Us How to Help Top 10 pages Follow us The storage capacity of these early read-only drives was less than 100 kilobytes. Floppy Disk Problems And Solutions
Verify that the floppy connection is connected to the motherboard FDD connector. On most PCs this is the DEL key, the F1 key or the F2 key. Helpful +1 Report delamuerte Aug 19, 2009 02:53AM dude you were sooo right disable you diskette ddirve, a thousand thanks Helpful +1 Report fara Nov 24, 2009 08:59PM When PC boots weblink That worked!
Novice mishandling of software or hardware settings can make your computer unusable and I take no responsibility for it.Tweet Share Email Share Related tips you might like How Floppy Disk Not Recognized Do you want to format it now?" or "A:\ is not accessible. He or she then views and interprets the signals with an oscilloscope.
Was this page useful? Thanks treefrog07 for your reply, except that it involves opening up the hard drive! The error was on integrated LAN on board. Floppy Disk Not Accessible the computer runs just fine when the menu pops up and I hit F1.
You can find it at Start | Programs | Accessories | System Tools | Scandisk. I would check all the the connectors first to be sure the data ribbon is properly attached to the FDD and to the motherboard, and that the power cable is firmed Thanks in advance for any advice Report jUNIOR- Mar 6, 2010 09:21PM THANKS A MILLION! :) Helpful +10 Report rapture Feb 2, 2009 02:04AM nevermind. http://bigvideogamereviewer.com/floppy-disk/floppy-drive-recovery.html I did a chkdskand the message I got ba More resources See also Windows 7 wont install, get error message "windows cannot br installed to this disk.
When the computer system needs to access data on the diskette, the read/write heads are stepped by signals generated by the computer system's floppy controller. Since common floppy drives don't have a sophisticated servo system, they must be carefully aligned in order to ensure the very important ability of reliably exchanging data diskettes with other drives. I solved the problem.