Home > Error Code > Flo Error Code On Hot Tub

Flo Error Code On Hot Tub

Contents

These are usually presented as FL, FLO or FLOW on your display, although it may be LF, for Low Flow, or PS for Pressure Switch. th2/current temperature = On startup indicates temperature probe problem. LF, or Low Flow error codes on a spa or hot tub is really a self-preservation exercise for your hot tub. Reply Speak Your Mind Cancel reply Name * Email * Website About Us We are a hot tub and sauna company with 3 showrooms located in the Philadelphia area. http://bigvideogamereviewer.com/error-code/fix-mac-error-code-43.html

Now, there is no action coming from the motor or the topside panel. Hold = Panel sensors have been pressed too many times in a short period of time. Topside controls also give lots of information about your spa status, which are not to be confused with spa error codes. All Rights Reserved. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/

Hot Tub Error Codes

Amesbury, Massachusetts 01913 Phone: 978-388-2585 Spring Hours: Monday - Friday: 10am-5pm Saturdays: 10am-3pm Sundays: Closed [emailprotected] Massachusetts In-ground Pool Design, Construction, and Service. Well sorry about long post any any misspelled words. Loading... Water was at 100 degrees this morning and everything was normal.

Unfortunately it is a process of elimination. -Jay Tim October 5, 2015 at 3:31 pm So I have a 2006 artesian dove canyon spa. Take a new one. At the same time this test is being done, put your hand on the stainless steel heater manifold, it should NOT be hot, it should only be at the same temperature Marquis Spa Error Codes let me know how that works. -Jay Howard July 31, 2014 at 7:32 am I have a Jacuzzi Model J-280 and I get a FS2 error code on the panel when

Thanks again. Where Is The Flow Switch On A Hot Tub When I power cycle the breaker, temperature reads 101 before the message shows up again. Thanks for any help or suggestions.

Thanks!

Now one more thing the tub is 8 years old bUt last winter,Mn, I winterized it, mayBe screwed something up! Balboa Hot Tub Error Codes I cleaned filters, still FLO code. We're going to jumper across these two leads right there just to make electrical contact between the two of them, FLO's gone. Anything you recommend?

Where Is The Flow Switch On A Hot Tub

Heater is shut down, but other spa functions run normally. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/ I have replaced every part of this hot tub all the way done to the wires and sensors. Hot Tub Error Codes With a complete retail pool store in Amesbury.

© 2014 Precision Pool Construction | 978-388-2585 | [emailprotected] Back to Top
Optimization WordPress Plugins & Solutions by W3 EDGE Hydropool Hot Tub Error Codes If not look for a certified service technician for your hot tub brand in your local area!

Note: The control system brand name is usually different from the hot tub brand name. this content If all else fails contact your local Sundance Support Desk to book a diagnostic and repair of your spa. HFL = Substantial difference between temperature sensors detected. Leave a Reply Click here to cancel reply. Vita Spa Error Codes

Ecn = Spa operating in Economy Mode. I disconnected the topside control panel and allowed it to dry out in the sun, thinking the blank screen was due to moisture. LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). weblink For Low Flow spa error codes, check the filter, check the pump and check the valves to find something that is obstructing the water flow.

You must be logged in to post a comment. Flc Error Code On Hot Tub You can check out this blog post here for more info on that: http://precisionpool.net/2010/10/how-to-release-an-air-lock-in-your-spa/ -Jay admin October 10, 2015 at 7:33 pm Hi Tim, Sounds like a bad relay or a Thank you!

If you have a small circulation pump in your spa this could be clogged with debris and causing low flow.

The light did come on above the heat sign but the flo error was still there. Posted in:hot tubs and spasspa troubleshooting See more Prev:In-ground Pool Installation Pictures Rowley, MA Back: All Posts Next:In-ground pool building permits, setbacks, and building codes About the Author JayB Jay is These error codes are similar to the ones previous, however we will be looking at these at another angle. Hot Tub Flow Switch Troubleshooting So we just keep turning it up to one turn.

I replaced the temp sensors but still get the error. I did some more troubleshooting online and found to adjust the pressure switch wheel. Bob karen June 22, 2012 at 10:41 am Hi I have a soleil vita spa. http://bigvideogamereviewer.com/error-code/fix-error-code-193.html Heater is deactivated.

FINAL NOTE: Most spas are equipped with pressure switches and can be found threaded into the stainless steel heater manifold. This sometimes refreshes the pc board software if there is anything funky going on. I mean, you could just bend a nail in half. Is anyone familiar with this make of hottub and would you be willing to provide me some feedback on next steps.

Pressure switch is not working. What we're gonna do right now is change a pressure switch. Heater disabled but the spa is operational. Now, if you have an FLC, which means it's reading closed when it's not running.

Today, I want to talk about two error codes that we get on the top site display. SN = Non functional high temperature sensor. You can leave a response, or trackback from your own site. Also last 2 things, first, when I turn one pump 2 and it hums for about 5 sec.

That's a lot right here. Any help would be great admin October 30, 2015 at 10:06 am Hi Shawn, If it is not the sensor than it must be the PC board itself. -Jay Jennie November The codes above are all related to flow issues or the pressure switch/flow switch and are the most common error codes. dr = Inadequate water detected in heater.

It's flashing a code and lighting up pump 2 light. You can find this info on the id sticker near the Sentry control box. Turn the power back on, you have five seconds to join the wires together, do not join them before you turn the power on. Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires.

Nigel August 19, 2016 Reply Damon if Summer Logic is causing the solid FLO it should go back to normal once the water cools. I have a LP warning. Gas Comparison More Hot tub low flow error causes and solutions…….